The Cube orange come with H7 processor with extra memory for
developers who want to run their own development code on The Cube.

ADS-B stands for Automatic dependent
surveillance—broadcast (ADS–B) is a surveillance technology in which an
aircraft determines its position via satellite navigation. ADS-B is used in
manned aircraft. Now onward The Cube Orange will come with carrier board which
will have ADS-B IN receiver built-in. This hardware will enable your UAV /
Drone to identify any manned aircraft flying nearby or approaching drone.
Autopilot will detect approaching and it will automatically adjust its position
so that no collision can take place.

ABS Molding ADS-B Introduction
A 1090MHz ADS-B receiver from uAvionix has been integrated into new ADS-B
carrier board. Autopilot equipped with the new unmanned system can receive
information about the location of manned aircraft in the area Information from
aircraft including position, altitude, speed, id, etc. can be viewed in Mission
Planner. Through parameter setting, you can optionally set up your cube orange
to allow the vehicle to automatically avoid aircraft Mat are detected in an
exclusion zone set by you.

How to use new ADS-B IN Carrier Board?

Carrier board has built in receiver. With the help of
mission planner if you are using Ardupilot or PX4 or any other firmware which
is supported by mission planner you can configure parameters for enabling or
disabling this feature. As of now this is optional but in future it might me
mandatory to activate ADS-B IN for avoiding UAV /Drone fly near manned
aircraft. This is restricted UAVs to enter into airspace which is for
Commercial or Private airspace.

Specifications of The Cube Orange

Processor :

STM32H753VIT6  (32 Bit ARM  Cortex -M7, 400 MHz, 2
MB flash, 1 MB RAM

STM32F100 (32 bit ARM  Cortex -M3 24 MHz 8KB SRAM)

Sensors : 

Accelerometer  ICM20948 / ICM20649 / IGM20602

Gyroscope ICM20948 / ICM20649 / 10420602

Compass ICM20948

Barometric Pressure Sensor MS5611x2

Operating Conditions and Performance

POWER input voltage / rated input current :  41-57V/25A

POWER rated output/input power       
          14W

USB port input voltage / rated input current 
4-57V/250mA

Servo rail input voltage       33V/5V

Operation Temperature -10°C / 55°C

This Product is not waterproof. External waterproof
protection is needed if you want to use it where there is chance of water make
come in contact with this product.

Key Design Points

Separate Cube with carrier board Lets users develop their
own carrier boards

Robust interface connectors to make it easy to plug and
safer during flight

Airframes VTOL, Plane , multicopter, Traditional Helicopter,
Rover, Boat, Sub, General robotics.

Heating System to fly under low temperature

3 Redundant IMU and up to 3 redundant GPS to make it safer

Fully support Intel Edison module

Standard power brick included with the full kit

Modular design with total Flexibility on connectivity.

Increased reliability and reduced integration complexity

It comes 100% RTK GPS ready.

Multiple GPS capability is standard.

The cube ( Pixhawk 2.1 ) has a total of 29 MEMS sensors in
it
3 X 3-axis Accelerometers
3 X 3-axis Gyroscopes
3 X 3-axis Magnetometers
2 X Barometers

Mechanical: 30×30 mm M3 mounting hole pattern, 35×35 mm
footprint
80 position DF17 connector. Carries all autopilot interface connections.
● Minimal (read: really minimal) electrical protection
● No power management
● 3.8 to 5.7V operation (absolute maximum ratings)
● 4.0 to 5.5V operation (compliant rating)

Total connectivity

● I2C2
● 2x CAN: CAN1 and CAN2
● 4x UART: TELEM1, TELEM2, GPS (I2C 1 embedded), SERIAL4(I2C 2 embedded)
● 1x Console: CONSOLE (SERIAL5)
● 1x HMI: USB extender

Ports and Pins on Carrier Board

5 Serial Ports
2 CAN ports
2 I2C ports
2 Power ports
1 ADC port
8 dedicated opto capable PWM out
6 GPIO that can also be used for PWM
Dedicated Spektrum RX port
S.Bus in and out, PPM in

For more details
please call +91878864106/ 6290425129/ 7001800105.